Lohmann cyclemotor, hard rubber drive roller, new manufacture.  £25 each.

Trojan Mini-Motor all steel drive roller.  £60 each.  SOLD OUT—machining more, work in progress.

Vincent Firefly steel drive roller assembly c/w metalastic core.  Service exchange—£70, or new—£80.
CURRENTLY SOLD OUT—MACHINING NEW STOCK—AVAILABLE AGAIN SHORTLY

Worn out Firefly drive rollers purchased for £5 each.

Itom Tourist all steel drive roller.  New - £65 each.

Bosch later type small 100mm Ø magneto flywheel puller—£18 each.
fits NVT, Morini Franco engines, Garelli (horizontal motor models), Flandria, KTM Hobby, etc.  Also early Bosch 1950s’ steel 115mm Ø magneto flywheel type as fitted to NSU Quickly, etc.
M22 × 1.5mm

Bosch 115mm Ø magneto flywheel puller for both early alloy & later type steel magneto flywheels.  £15 each.
M26 × 1.5mm.

Ducati Cucciolo mag flywheel puller—£18
M22 × 1mm.

Firefly drive roller extractor—£12 each.

Honda mag flywheel puller—£14 each.
Dual-end threads for:
M24 × 1mm = P50, PC50, etc;
M27 × 1mm LH thread = C100, C50/70/90, etc

Itom Tourist cyclemotor original ‘composite’ drive roller extractor—£15 each.
M24 × 1.5mm.

Itom Tourist Replacement drive roller extractor—£12 each.

Kerry Capitano / Minarelli / CEV / Dansi mag flywheel puller.  Fits 2-port & 3-port CEV magneto flywheel types—£15 each.
M19 ×1mm.

Lavalette / Paloma / Hercules Corvette mag flywheel puller—£18.
M22 × 1mm.

Manurhin Hobby scooter mag flywheel puller—£15 each.
M24 × 1.5mm.

Miller type BS9 2-hole zinc mag flywheel with centre boss puller—£20.
4×holes @ 1⁵/16" PCD.  4×2BA screws included with kit.  Also fits Wipac Series-90 4-hole ‘ported’ mag flywheel.

Miller type FW17 magneto flywheel extractor for Phillips Gadabout P39/P50, Panda Mk1/Mk2, Hercules Her-cu-motor, BSA Winged Wheel, etc—£16 each.

Miller type W7 3-hole brass mag flywheels with centre boss.  Extractor set—£20.
3 × holes @ 1¼" PCD.
The 3 threaded holes in the mag flywheel are No.6 ANC/UNC 0.138"Ø × 32tpi, and 3 machine screws are included with the kit.  For early Trojan Mini-Motor models, etc.

Mobylette/Raleigh clutch drum extractor (Blunt-end drive pin)—£12 each.

Mobylette/Raleigh points cam extractor—£15 each.
M26 × 1mm.

Moto-Guzzi Stornello 125 magneto flywheel puller—£18
May also fit other small capacity Moto-Guzzi magsets.
M22 × 1mm.

NVT Easy Rider (Morini Franco engine) / Bosch 100mm Ø mag flywheel puller—£18 each.
M22 × 1.5mm.

Peugeot (all moped models)—£15 each.
M20 × 1mm.

Raleigh RM1/RM2 Sturmey–Archer engine Lucas mag flywheel puller—£18.
M22 × 1.5mm.

Raleigh RM1/RM2 Sturmey-Archer engine.  Drive pulley extractor 1"BSF×10tpi (internal thread)—Sold Out
Note: please don't try to prise this pulley off instead!  They're always very tight on the shaft.  The pulley is made of brittle cast iron and snaps like a biscuit, then it's a bit late to find out that replacements are practically unobtainable.

Sachs clutch centre extractor & Sachs 98cc autocycle magneto flywheels—£15 each.
M27 × 1.25mm.

Simson/MZ50 (all models), Rhienmetal/Soemtron engines, Optima magneto flywheel puller—£15 each.
M27 × 1.25mm.

Villiers 3K magneto flywheel puller—£15 each.
7/8" UNF × 14 TPI.
As used in Phillips P45 Gadabout, Norman Nippy Mk2 type-2, Norman Nippy Mk4, Norman Lido Mk1, Ambassador Moped, etc.

Wipac 3-hole mag flywheel puller—£20 each.
For Wipac Bantamag & Wipac Series-90 (plain/un-ported) mag flywheels.  3 × holes @ 1¼" PCD
Note: Since Bantamag flywheels can be variously found with either 2BA or 3BA threaded extraction holes, this kit comes complete with both threaded bolt sizes.  Use correct thread to suit.

Wipac 4-hole mag flywheel puller—£15 each.
For Wipac Series-90 (ported) mag flywheels.  4 × holes 2BA @ 1 5/16" PCD.

Wipac Series-90 4-hole ‘ported’ mag flywheel puller—£20.
4×holes @ 1⁵/16" PCD.  4×2BA screws included with kit.  Also fits Miller type BS9 2-hole zinc mag flywheels with centre boss.

Wipac S1233 magneto flywheel extractor for Scott Cyc-Auto.—£20 each.